Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,732. Welcome to our newest member, Miss Allison
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 06-26-2012, 07:13 AM
P.F.C. P.F.C. is offline
Steel
 
Join Date: May 2012
Location: West Virginia
Posts: 17
Default how much will it run me?

what is the avrage start up cost for an air graver and all to tools i will need to get started? i have been looking around but i really dont know enough about what i need to get a good price quote. i was thinking it would cost me some where near 5K just for tools and setup not inculding classes.
Reply With Quote
  #2  
Old 06-26-2012, 08:39 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: how much will it run me?

Quote:
Originally Posted by P.F.C. View Post
what is the avrage start up cost for an air graver and all to tools i will need to get started? i have been looking around but i really dont know enough about what i need to get a good price quote. i was thinking it would cost me some where near 5K just for tools and setup not inculding classes.
Hi PFC,

You can choose from these sets ;

http://www.airgraver.com/Hand_Engrav...graving%20Sets

Get an engraving block ;

http://www.airgraver.com/Engraving_Blocks.htm

A medium range compressor and a good strong worktop and you are ready to start I believe,
Scopes and the rest is an option .

SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #3  
Old 06-26-2012, 12:59 PM
P.F.C. P.F.C. is offline
Steel
 
Join Date: May 2012
Location: West Virginia
Posts: 17
Default Re: how much will it run me?

im sure this has been covered many times now but what are the major differences between palm controle and foot control? and does the goliath vise open wide enough for a rifle action?
Reply With Quote
  #4  
Old 06-26-2012, 09:18 PM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,359
Default Re: how much will it run me?

Palm control, uses less air, no foot hand issues,easy to learn /use. Yes not cheap but the tools are a investment, I have been using my air gravers for around 10 years now and no problems, about 4 to 6 hrs a day. I believe the vice you mentioned will handle most firearms.
Reply With Quote
  #5  
Old 06-27-2012, 08:19 AM
P.F.C. P.F.C. is offline
Steel
 
Join Date: May 2012
Location: West Virginia
Posts: 17
Default Re: how much will it run me?

awesome. thank you for the info. we had to buy two rotary tools for my wifes engraving work the first one was a low grade NSK and the second was a much better tool but i dont know the name its a 500 something or other.
i hate buy things twice and i found if you start with the best that it will serve you best.
Reply With Quote
  #6  
Old 06-27-2012, 08:57 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: how much will it run me?

Hi PFC,

When you buy tools always buy the best in the beginning,they will pay pay you back and more.

SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #7  
Old 06-28-2012, 11:19 AM
hobochief hobochief is offline
Gold
 
Join Date: Sep 2010
Location: Florida
Posts: 140
Default Re: how much will it run me?

If you are looking for and engraving ball I have some used ones from $150.00 to 300.00 with attachments, also I have a simple ball vise that holds Steve"s nickel holder for $85.00 that is for NICKEL CARVING only.. Welcome to the group. We will have both the classic and palm control at the FUN SHOW in Orlando Fl july 12 thru 14th if you are in FLorida on Vacation of something. PM me for more information or see thread of show..
Archie/hobochief/Pres Original Hobo Nickel Society...
Reply With Quote
  #8  
Old 06-28-2012, 04:34 PM
P.F.C. P.F.C. is offline
Steel
 
Join Date: May 2012
Location: West Virginia
Posts: 17
Default Re: how much will it run me?

thanks for the offer. it will be some time before i can invest in tools so far my wifes work hasnt made us enough to allow me to get started. we will probably wait until after we get taxes back in the spring that way we can get the tools and classes all at once for now i plan to work with her rotary hand piece and help her in the shop.
what are some websites i could look at to find metal to work with? all i have is blank scrap steel. where do i get silver and copper to work on?
Reply With Quote
  #9  
Old 06-28-2012, 05:05 PM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: how much will it run me?

Quote:
Originally Posted by P.F.C. View Post
thanks for the offer..
what are some websites i could look at to find metal to work with? all i have is blank scrap steel. where do i get silver and copper to work on?
Hi,

Try Ebay or ;
http://www.onlinemetals.com/merchant...owunits=inches

SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #10  
Old 09-28-2012, 07:54 PM
William47 William47 is offline
Copper
 
Join Date: Sep 2012
Location: Georgia
Posts: 5
Default Re: how much will it run me?

Do you still have the ball vice for the nickel carvings? I am interested. Willy770@bellsouth.net
Reply With Quote
  #11  
Old 09-29-2012, 02:05 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: how much will it run me?

Quote:
Originally Posted by William47 View Post
Do you still have the ball vice for the nickel carvings? I am interested. Willy770@bellsouth.net
Hi William47,

For nickel carving ,the nickel holder is ideal ;

http://www.airgraver.com/images/Nickel-holder.jpg

Unless if you wish to use a ball vise.

SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #12  
Old 09-30-2012, 12:04 PM
Baysider Baysider is offline
Steel
 
Join Date: Jun 2011
Location: Onancock, Virginia, USA
Posts: 49
Default Re: how much will it run me?

Try Metalliferous.com, they have just about everything and the prices are very competitive, and sometimes you can catch some really good deals. I am not a professional engraver and only active for about 2 years but like everyone says you can not go wrong with Steves tools. I splurged about a year ago ans got an Artisan foot control and it made an imediate positive impact on my work. My budget is tight also my other major expense was my Pepe vise, the smallest one, and Steve's templates along with diamond stones and of course the gravers. all are adequete formy level of work and knowledge. Also found a pancake compressor on sale at Harbour frieght for $39, its loud but serves the purpose. Of course the most valuable tool/resourse is this forum, these guys are the best and ever sharingnwith their vast knowledge.
Reply With Quote
  #13  
Old 09-30-2012, 12:25 PM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: how much will it run me?

Hi,
I have tried a ball vise for nickels and sadly I must say the nickels turn in it while you are working on them,so I have requested for a nickel holder from Steve L.

SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 01:04 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.