Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,763. Welcome to our newest member, mtan1446
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Tutorials and Contests - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 04-01-2009, 09:02 PM
MikeDubber's Avatar
MikeDubber MikeDubber is offline
Platinum
 
Join Date: Jun 2007
Location: Evansville, Indiana
Posts: 510
Default Mike Dubber - The Bowen SSA Rod Fixture

I've been field testing some of Fred Bowen's Colt SAA Fixtures. Today I used his newest, the Bowen SAA Ejector Rod Housing Fiixture.
If you've engraved a Colt SAA you surely know that the ejector rod housing (ERH) is a tuff little critter to hold and engrave. The ERH part is all about curves, much like a barrel, and it is hollow, open on the bottom where the ejector slides, and it will deform/crush if enough vise pressure is applied. Worse of all, the diameter is only 3/8"

The following photos were taken today as I worked my way through a SAA rod housing that was to be engraved and inlaid in gold. You can see Fred's design for the holder in photo #1. The end peices have 3/8" pins that fit in most engraving blocks (this one is my LeTourneau) and there is a steel rod that extends from one side to the other and through the center of the housing - that eliminates vibration and supports the hollow ERH. There are nylon washers at each end that allow the engraver to tighten the block enough to hold everything securely, but to also allow movement (rotation) of the housing as the part is engraved.

Next, the gold inlay areas are excavated and burred up to accept gold wires. This process, and the subsequent setting procedure, is somewhat less than "delicate," so I was very pleased that my Bowen Fixture held everything tightly enough to do the excavation, burring and inlaying...I experienced no vibration or movement throughout the process.

And, finally, here is a closeup of the finished work...so you see, my friends, engraving just gets easier and easier all the time. But I must qualify all of this by admitting that I did all of the work with my PalmControl - that's the real first step to engraving success!
Reply With Quote
  #2  
Old 04-01-2009, 09:48 PM
Tom McArdle's Avatar
Tom McArdle Tom McArdle is offline
Platinum
 
Join Date: Apr 2006
Location: Western NY USA
Posts: 1,040
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

Thanks Mike!

beautiful!

You are right, those things are a bear to work on. Does he have other SAA fixtures? How much? How do we get in touch with him?

Take care,

Tom
__________________
Tom McArdle
Reply With Quote
  #3  
Old 04-02-2009, 07:45 AM
MikeDubber's Avatar
MikeDubber MikeDubber is offline
Platinum
 
Join Date: Jun 2007
Location: Evansville, Indiana
Posts: 510
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

Fred Bowen can be contacted via e-mail at
stagargent@yahoo.com
Reply With Quote
  #4  
Old 04-02-2009, 07:53 AM
ron ron is offline
Platinum
 
Join Date: Apr 2006
Location: harrisburg pa
Posts: 780
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

hi Mike .. thanks for sharing your work with us , just beautiful work and great gold inlay work . i use some thing similar to what you a using but it is the jig i use for engraving and gold inlaying barrels .. ron p
Reply With Quote
  #5  
Old 04-02-2009, 09:20 AM
MikeDubber's Avatar
MikeDubber MikeDubber is offline
Platinum
 
Join Date: Jun 2007
Location: Evansville, Indiana
Posts: 510
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

Hey Ron:

What do you use for holding SAA hammers?
While I'm here, I might also say that some of us would to see some similar photo detail of how you do your inlay scroll and floral - it's very delicate, creative and beautifully designed.

Mke
Reply With Quote
  #6  
Old 04-02-2009, 05:50 PM
ron ron is offline
Platinum
 
Join Date: Apr 2006
Location: harrisburg pa
Posts: 780
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

hi Mike .. to hold my hammers i use a product called cerasafe . i set the hammer into it and when it hardens i hold it in my vise .

on my inlays i inlay my leafs first , when you under cut the whole scroll you take a chance of destroying the under cut you made on the spine , so i only under cut the leaf first .. here are some photos of how i do it also some photos of the jig i use to hold the ejector tube and barrels . no problem cutting with this jig ..

hey when are you going to come to my shop for a couple of days and show me how you do your raised figure inlays on the recoil shield and i will show you some of my inlay tricks .. give me a call .. ron p
Attached Images
File Type: jpg Gun Engraving 1835.jpg (28.8 KB, 159 views)
File Type: jpg Gun Engraving 1838.jpg (176.7 KB, 158 views)
File Type: jpg Gun Engraving 1840.jpg (28.9 KB, 168 views)
File Type: jpg Gun Engraving 1844.jpg (32.7 KB, 161 views)
Reply With Quote
  #7  
Old 04-02-2009, 07:42 PM
MikeDubber's Avatar
MikeDubber MikeDubber is offline
Platinum
 
Join Date: Jun 2007
Location: Evansville, Indiana
Posts: 510
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

Thanks Ron - your methods and mine are somewhat the same, although I think that yout leaf inlay procedure makes more sense than using wires like I do. Yes, we should get together and spend some time at the bench trading skills. Maybe next Fall will be a good time - I'll put it on my list.

Mike
Reply With Quote
  #8  
Old 04-02-2009, 08:23 PM
ron ron is offline
Platinum
 
Join Date: Apr 2006
Location: harrisburg pa
Posts: 780
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

hi Mike .. i would be honored for you to come to my shop and i will show you some of my methods for inlaying and holding colt parts , i do use wire for the leaf inlay , it is 18 ga . that i flatten out to form a sheet . also i use the same barrel fixture for holding the colt frames , i can turn the frame in any direction while engraving with this fixture .. well looking forward to us getting together .. ron p
Reply With Quote
  #9  
Old 04-02-2009, 10:35 PM
WVEngraver's Avatar
WVEngraver WVEngraver is offline
Platinum
 
Join Date: Apr 2008
Location: Tennessee
Posts: 1,656
Default Re: Mike Dubber - The Bowen SSA Rod Fixture

Great following along with you guys. Great selection of photos Mike and Ron.

Many thanks!!

Chris
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 09:21 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.